DVS Ember-Fyre Burner (Version 2.1 Log) Installation .

1y ago
10 Views
0 Downloads
1.13 MB
8 Pages
Last View : 19d ago
Last Download : n/a
Upload by : Callan Shouse
Transcription

DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Compatibility DVS GSR NB InsertPacking List DVS Ember-Fyre Burner AssemblyNG and LP Air DeflectorsLeft and Right Ember Trays8-Piece Log SetBag of Rock WoolBag of Log EmbersPreparing the Burner1.Remove the 3 screws on the back of the burner.2. Attach the correct air deflector to the burner with the screws removed earlier. Note how the LP airdeflector has a notch along the bottom.NG Air DeflectorPage 1 of 817601874 — 1/15/16LP Air Deflector Travis Industries, Inc.

DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Burner InstallationInstall the burner as shown below (make sure the burner is fully seated over the orifices and pushed allthe way to the right). Install the side ember trays.Page 2 of 817601874 — 1/15/16 Travis Industries, Inc.

DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Log Set Installation!The logs are fragile, especially after being exposed to heat. Make sure the gas control valve is “OFF” and the heater is cool prior to conducting service. Failure to position the parts in accordance with these diagrams or failure to use only partsspecifically approved with this appliance may result in property damage or personal injury. If using propane (LP), convert the appliance before installing the burner and logs. The burner must be correctly positioned before installing the logs. Make sure the burner is fullyseated and the pilot is properly aligned.Rear Log PlacementThe rear log has two holes on the bottom. Place the log so the pins on the burner insert into theholes on the log (see photos below).NOTE: On LP inserts, pushthe log to the back. On NGinserts, pull the log forward.Page 3 of 817601874 — 1/15/16 Travis Industries, Inc.

DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Left Front Log PlacementThe left front log has two holes on the bottom. Place the log so the pin on the burner and the metalbracket insert into the holes on the log (see photos below).NOTE: On LP inserts, pushthe log to the back. On NGinserts, pull the log forward.Right Twig PlacementPlace the right twig on the burner as shown below. Make sure it does not cover any burner holes.Page 4 of 817601874 — 1/15/16 Travis Industries, Inc.

DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Right Front Log PlacementThe right log has two holes on the bottom. Place the log so both burner pins insert into the holeson the log (see photos below). Make sure the log is pushed back so it sits flat.NOTE: On LP inserts, pushthe log to the back. On NGinserts, pull the log forward.Left Cross Log PlacementPlace left cross log as shown below. Note- how the log rests on the flat spots of the back and leftlogs.Page 5 of 817601874 — 1/15/16 Travis Industries, Inc.

DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Right Cross Log PlacementPlace the log as shown below. The right cross log rests on the flat spots of the rear and the right frontlogs.Left Twig PlacementPlace the left twig on the burner as shown below. Make sure it does not cover any burner holes.Page 6 of 817601874 — 1/15/16 Travis Industries, Inc.

DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Center Twig PlacementPlace the center twig on the burner as shown below. Make sure it does not cover any burner holes.The completed installation is shown below.Page 7 of 817601874 — 1/15/16 Travis Industries, Inc.

DVS Ember-Fyre Burner (Version 2.1 Log)Installation Instructions (SKU 96900105)Ember PlacementPlace a layer of embers along any screw heads and visible edges of the burner.Rockwool InstallationThe included rock wool is placed on top of the burner to enhance the glow from the burner. The rockwool works best when it is applied in a very thin, porous layer. The best method for applying therock wool is to brush it on to the burner. Compress a clump of rockwool between your thumb andforefinger. Use a stiff brush to apply a thin layer of rockwool fibers onto the burner. Do not use theentire bag of rockwool. Use only a small amount and save the remainder. Over-use of rockwool willdiminish the glow and may cause sooting or other adverse conditions.Page 8 of 817601874 — 1/15/16 Travis Industries, Inc.

Ember Placement Place a layer of embers along any screw heads and visible edges of the burner. Rockwool Installation The included rock wool is placed on top of the burner to enhance the glow from the burner. The rock wool wo